Difference between revisions of "Metal Lathe"
Jump to navigation
Jump to search
Line 14: | Line 14: | ||
**5/8 & 3/4" dia. round boring bars | **5/8 & 3/4" dia. round boring bars | ||
**1/2" x <=3/16" parting blades | **1/2" x <=3/16" parting blades | ||
+ | |||
+ | == Training Requirement == | ||
+ | YES, introduction, one-on-one | ||
+ | |||
+ | == Safety Requirement == | ||
+ | *Eye Protection | ||
+ | *Short Sleeves | ||
+ | *Long hair tied back | ||
+ | *No gloves or jewelry | ||
+ | |||
+ | == Cleanup requirement == | ||
+ | *Tools put on shelf | ||
+ | *Material removed from chuck | ||
+ | *Chips swept & vacuumed from all surfaces (carriage, chip pan, floor) | ||
+ | |||
+ | == Contact == | ||
+ | metalshop AT makerspacenanaimo DOT org | ||
+ | *Jordan P. | ||
+ | *Jordan B. | ||
+ | *Dan S. | ||
+ | |||
+ | == Approved materials == | ||
+ | '''NO HARDENED STEEL''' - a hand file must be able to cut it (< Rc 35) | ||
+ | *Aluminum (6061, 7075) | ||
+ | *Steel (1018 mild steel, 12L14 leaded, 4140) | ||
+ | *Stainless Steel (303,304,316,17-4PH) | ||
+ | *Bronze | ||
+ | *Brass | ||
+ | *Plastic (UHMW, Acetal, Acrylic, Polycarbonate) | ||
+ | |||
+ | == Approved cutting fluids == | ||
+ | '''NO WATER-BASED FLUIDS''' | ||
+ | |||
+ | For Aluminum: | ||
+ | *WD-40 | ||
+ | *Relton A-9 | ||
+ | For Steel: | ||
+ | *Tap Magic | ||
+ | *Rapid Tap | ||
+ | *Any light/dark thread cutting oil | ||
== Learning == | == Learning == |
Revision as of 22:05, 13 January 2019
About
- Make: Shaoxing
- Model: CQ6230 (same as Grizzly G4003G)
Documentation
- User's Manual
- Metal Shop Reference Material
- Uses an AXA-style quick change tool post
- up to 1/2" square tools
- 5/8 & 3/4" dia. round boring bars
- 1/2" x <=3/16" parting blades
Training Requirement
YES, introduction, one-on-one
Safety Requirement
- Eye Protection
- Short Sleeves
- Long hair tied back
- No gloves or jewelry
Cleanup requirement
- Tools put on shelf
- Material removed from chuck
- Chips swept & vacuumed from all surfaces (carriage, chip pan, floor)
Contact
metalshop AT makerspacenanaimo DOT org
- Jordan P.
- Jordan B.
- Dan S.
Approved materials
NO HARDENED STEEL - a hand file must be able to cut it (< Rc 35)
- Aluminum (6061, 7075)
- Steel (1018 mild steel, 12L14 leaded, 4140)
- Stainless Steel (303,304,316,17-4PH)
- Bronze
- Brass
- Plastic (UHMW, Acetal, Acrylic, Polycarbonate)
Approved cutting fluids
NO WATER-BASED FLUIDS
For Aluminum:
- WD-40
- Relton A-9
For Steel:
- Tap Magic
- Rapid Tap
- Any light/dark thread cutting oil
Learning
- Videos 203-206 Lathe 1/4 to 4/4
- First Project - Positioning Hammer
- Videos - Thatladymachinist 013-017
- Drawings
Vendors
Raw Materials | Hardware | Tooling & Accessories |
---|---|---|
|
|
Machine Specifications
Specifications | Standard Equipment | Features | |||
---|---|---|---|---|---|
|
|
|